Modules & Accessories
Home > Telephony Cards > Modules and Accessories
We have What You Need
Add-on hardware modules and accessories for analog and digital cards.
Telephony Card Add Ons
Echo cancellation
DSP-based echo cancellation modules for all of our analog and digital (T1/E1/J1) cards with the VPMOCT series modules.
- 1VPMOCT256LF – Two Hundred and Fifty-Six (256) Channel Hardware Echo Cancellation Module
- 1VPM128LF – One Hundred and Twenty-Eight (128) Channel Hardware Echo Cancellation Module
- 1VPMOCT128LF – One Hundred and Twenty-Eight (128) Channel Hardware Echo Cancellation Module
- 1VPM064LF – Sixty-four (64) Channel Hardware Echo Cancellation Module
- 1VPMOCT064LF – Sixty-four (64) Channel Hardware Echo Cancellation Module
- 1VPM032LF – Thirty-two (32) Channel Hardware Echo Cancellation Module
- 1VPMOCT032LF – Thirty-two (32) Channel Hardware Echo Cancellation Module
Analog FXS Module Power Supply
FXS modules provide ringing voltage and battery to telephones or handsets and require substantial amount of 12V DC power in order to operate properly. The PCI interface on motherboards cannot provide sufficient quantities of this voltage necessary to ring 4, 8 or 24 modules. As a solution, Digium analog cards are mounted with a 4-pin disk-drive or Molex connector on the base board. This connector must be supplied with an internal power connector from the system’s power supply if FXS modules are in use.
- 1PWR2401BLF – One external power supply bundle for analog card station (FXS) modules
- 1PWR2402BLF – Two external power supply bundle for analog card station (FXS) modules
Single Channel Analog Modules
Digium single channel analog modules allow 400 Series or 800 Series telephony cards to terminate one (1) line (FXO) or station (FXS) connections per module.
- 1S100MF – Single Channel Station (FXS) Module
- 1X100MF – Single Channel Trunk (FXO) Module
- 1X100MF – Single Channel Trunk (FXO) Module
Quad Channel Analog Modules
Digium quad channel analog modules allow 800 Series or 2400 Series telephony cards to terminate four (4) line (FXO) or station (FXS) connections per module.
- 1S400MF – Quad Channel Station (FXS) Module
- 1X400MF – Quad Channel Trunk (FXO) Module
Low Profile Brackets
Digium Telephony boards come standard with full-height brackets for standard mounting. Optional low-profile brackets are available for all low-profile cards to enable mounting into 1-U servers.
Product Code: 3244-00052
Description: Low Profile Bracket for Four (4) port A4 analog cards
Product Code: 3244-00044
Description: Low Profile Bracket for One (1) Span TE133 and TE134 Digital Cards
Product Code: 3244-00048
Description: Low Profile Bracket for Two (2) Span TE235 Digital Card
Product Code: 3244-00049
Description: Low Profile Bracket for Four (4) Span TE435 Digital Card
Cables And Accessories
Straight-through and cross-over cables for connecting Digium T1/E1 interface cards and T1/E1 ports, telephone cables for interfacing analog cards, and timing cables for digital cards.
Product Code: 3113-00016
Description: Seven (7) Foot T1/E1 cable, cross-over, shielded
Product Code: 1ACC24PPP
Description: Twenty-four (24) port RJ-11 Nineteen (19) inch rack mount patch panel for 24 port analog cards
Product Code: 3113-00002
Description: Six (6) Foot 50-pin Male-to-Female cable for Twenty-Four (24) port analog cards
Product Code: 3112-00001
Description: Four (4) port interlocking timing cable for two (2) and four (4) span digital T1/E1 cards
Product Code: 3112-00003
Description: Three (3) port interlocking timing cable for HX8 and TE8XX series cards
Product Code: 3244-00010
Description: One low profile bracket for TC400 and TCE400 VoIP transcoding cards
Specialty Tools
Power Adapter
The Sangoma Power Adapter draws +12 V power from your standard PCIe slot and sends it to a standard Molex connector. Its unique design does not reduce the number of PCIe slots available in your system.
SKU: ST1
Crimping Tool
Use this kit of twelve RJ11/4 plugs and a crimping tool to hardwire your Sangoma A200 system.
SKU: ST2
Telco Patch Panel, 6 Position 2 Conductor, 24 Port/1 RMS
- 24-port
- 1 rack mount space (RMS)
- Integrated with 1 Telco connector
- Includes # 12 rack screws
- Use female amphenol connector
- 6 position, 2 conductor
SKU: STPP24
Sangoma Tapping Tool
Sangoma’s T1/E1 line tapping solution is a high performance, robust and inexpensive toolkit that gives you complete access to the T1/E1 voice and signalling interfaces. Based on the popular A102, A104 and A108 AFT cards, the system supports the line tapping of one, two and four T1/E1 lines per card respectively.
Cables & Connectors
Seven Foot T1/E1 Cable, Cross-Over, Shielded
The 7 foot shielded, cross-over cable is used for connecting Digium T1/E1 interface cards to the PSTN or other T1/E1 equipments. The cross-over cable is the standard cable that should be used to connect T1/E1 ports to T1/E1 ports or equipment.
Product Code: 3113-00016
Twenty-four Port Rack Mount Patch Panel
The Digium 2400P Rack Mount Breakout Box is a 19 inch 1U, rack mountable patch panel featuring a 50-pin male connector and its 24 female RJ-11 connectors are wired with two conductors for single line operation.
Product Code: 1ACC24PPP
Six Foot 50-pin Male-to-Female Cable
The 6 foot 50-pin telephone cable interfaces the TDM2400P card with regular RJ-11 two-conductor telephone cables and is used in combination with either the 24-port, 2-wire breakout box (ACC2400PBO), or the 24-port, 2-wire 19″ rack mount unit (ACC2400PPP)
Product Code: 3113-00002
Four Port Interlocking Timing Cable
up to four TE2/4XXP cards to share the same sync (timing) source from the T1/E1 provider, or provide a consistent sync source across multiple cards.
Product Code: 3112-00001
Three Port Interlocking Timing Cable
The timing cable allows up to three Hx8 or TE8xx cards to share the same sync (timing) source from the T1/E1 provider, or provide a consistent sync source across multiple cards.
Product Code: 3112-00003
RF Cable
SKU: CABL-647
7 feet length twisted pair Cable
SKU: CABL-650
Open-ended Cable with SCSI Type Connector to Panel
SKU: CABL-649
2-Ends Cable with SCSI Type connector
SKU: CABL-648
Single-mode fiber, LC duplex connectors
SKU: CABL-651
A108 T1/E1 “Portsplitter” Cable
SKU: CABL-630
A142 Split RS232
Standard cable for A142R
SKU: CABL-636
A142 Split V.35 / EIA530
Standard cable for A142V
Standard | ROHS: Yes | Length: 1′
SKU: CABL-637
A144 Octopus RS232
Standard cable for A144R
Standard | ROHS: Yes | Length: 1′
SKU: CABL-638
A144 Octopus V.35/EIA530
Standard cable for A144V
Standard | ROHS: Yes | Length: 15′
SKU: CABL-639
A200 Analog Cable
A200 Analog Cable
Standard | ROHS: Yes | Length: 6′
SKU: CABL-629
A400 Amphenol Y
Dual DB25 to Amphenol cable for the A400
Request | ROHS: Yes | Length: 6′
SKU: CABL-632
A400 DB25 Hard-wire Cable
For a A400 Analog Cards
Standard | ROHS: Yes | Length: 6′
SKU: CABL-631
B600 FXO Cable
FXO Cable for the B600
Standard | ROHS: Yes | Length: 6′ | TBD = Price for this item will be determined by a Sangoma representative on per order basis. Please contact us if you have any questions.
SKU: CABL-643
BRI Cable
For the A500 BRI
Standard | Length: 6′
SKU: CABL-634
Dual Synch Cable
Dual Synch Cable
Only Sold Separately | ROHS: Yes | Length: 8”
SKU: CABL-633A
EIA530 DCE Cable
For Sangoma cards
Special Order | ROHS: Optional | Length: 4′ | TBD = Price for this item will be determined by a Sangoma representative on per order basis. Please contact us if you have any questions.
SKU: CABL-611
Fax Synch Cable
Fax Synch Cable
Only Sold Separately | ROHS: Yes | Length: 8′
SKU: CABL-633
Molex Power Adapter
Power Adapter for FXS
Only Sold Separately | ROHS: Yes | Length: 8″
SKU: CABL-635
RJ45 E1/T1 Cross over Cable
Back-to-back, cross over cable (x/o)
Special Order | ROHS: Yes | Length: 20’
SKU: CABL-614C
RJ45 E1/T1 Cable
RJ45 E1/T1 Cable
Standard | ROHS: Yes | Length: 6′
SKU: CABL-614G
RS232 Back-to-Back Cable
For connecting Sangoma cards to 3rd party DTEs
Special Order | Length: 4′ |TBD = Price for this item will be determined by a Sangoma representative on per order basis. Please contact us if you have any questions.
SKU: CABL-602
RS232 Back-to-Back Null-modem Cable
Special Order
Only Sold Separately | Length: 10′ |TBD = Price for this item will be determined by a Sangoma representative on per order basis. Please contact us if you have any questions.
SKU: CABL-601
RS232 DCE Cable
For the A142, A144
Standard | ROHS: Yes | Length: 6′
SKU: CABL-607
SATA-Molex Power Adapter
SATA-Molex Power Adapter
Only Sold Separately | ROHS: Yes | Length: 6″
SKU: CABL-640
T3 coax cables (Tx and Rx pair)
1 pair of 6’ BNC shielded Coaxial Cable for DS-3 Tx and Rx
SKU: CABL-646
USB FXO / B600 FXS Cable
For the USBfxo and B600 FXS
Standard | Length: 6′ TBD = Price for this item will be determined by a Sangoma representative on per order basis. Please contact us if you have any questions.
SKU: CABL-642
USB FXO USB Cable
For the USBfxo
Standard | Length: 6′ TBD = Price for this item will be determined by a Sangoma representative on per order basis. Please contact us if you have any questions.
SKU: CABL-641
V.35 Back-to-Back Cable
Special Order | ROHS: Optional | Length: 10′ TBD = Price for this item will be determined by a Sangoma representative on per order basis. Please contact us if you have any questions.
SKU: CABL-610
V.35 DCE Cable
For the A142, A144
Standard | Male | ROHS: Yes | Length: 6′
SKU: CABL-608
X.21 DCE Cable
For Sangoma cards
Only Sold Separately | Length: 6′
SKU: CABL-613