© 2023 All rights reserved
Telephony Cards
Menu
We Have the Modules and Accessories You Need
Add-on hardware modules and accessories for analog and digital cards.
Contact Sales



Telephony Card Add-Ons
Single Channel Analog Modules
Digium single channel analog modules allow 400 Series or 800 Series telephony cards to terminate one (1) line (FXO) or station (FXS) connections per module.
1S100MF - Single Channel Station (FXS) Module
1X100MF - Single Channel Trunk (FXO) Module
1X100MF - Single Channel Trunk (FXO) Module
Quad Channel Analog Modules
Digium quad channel analog modules allow 800 Series or 2400 Series telephony cards to terminate four (4) line (FXO) or station (FXS) connections per module.
1S400MF - Quad Channel Station (FXS) Module
1X400MF - Quad Channel Trunk (FXO) Module
Low Profile Brackets
Digium Telephony boards come standard with full-height brackets for standard mounting. Optional low-profile brackets are available for all low-profile cards to enable mounting into 1-U servers.
3244-00052 - For Four (4) port A4 analog cards
3244-00044 - For One (1) Span TE133 and TE134 Digital Cards
3244-00048 - For Two (2) Span TE235 Digital Card
3244-00049 - For Four (4) Span TE435 Digital Card
Analog FXS Module Power Supply
FXS modules provide ringing voltage and battery to telephones or handsets and require substantial amount of 12V DC power in order to operate properly. The PCI interface on motherboards cannot provide sufficient quantities of this voltage necessary to ring 4, 8 or 24 modules. As a solution, Digium analog cards are mounted with a 4-pin disk-drive or Molex connector on the base board. This connector must be supplied with an internal power connector from the system's power supply if FXS modules are in use.
1PWR2401BLF - One external power supply bundle for analog card station (FXS) modules
1PWR2402BLF - Two external power supply bundle for analog card station (FXS) modules
Echo cancellation Modules
DSP-based echo cancellation modules for all of our analog and digital (T1/E1/J1) cards with the VPMOCT series modules.
1VPMOCT256LF - Two Hundred and Fifty-Six (256) Channel Hardware
1VPM128LF - One Hundred and Twenty-Eight (128) Channel Hardware
1VPMOCT128LF - One Hundred and Twenty-Eight (128) Channel Hardware
1VPM064LF - Sixty-four (64) Channel Hardware
1VPMOCT064LF - Sixty-four (64) Channel Hardware
1VPM032LF - Thirty-two (32) Channel Hardware
1VPMOCT032LF - Thirty-two (32) Channel Hardware
Cables and Accessories
Straight-through and cross-over cables for connecting Digium T1/E1 interface cards and T1/E1 ports, telephone cables for interfacing analog cards, and timing cables for digital cards.
3113-00016 - Seven (7) Foot T1/E1 cable, cross-over, shielded
1ACC24PPP - Twenty-four (24) port RJ-11 Nineteen (19) inch rack mount patch panel for 24 port analog cards
3113-00002 - Six (6) Foot 50-pin Male-to-Female cable for Twenty-Four (24) port analog cards
3112-00001 - Four (4) port interlocking timing cable for two (2) and four (4) span digital T1/E1 cards
3112-00003 - Three (3) port interlocking timing cable for HX8 and TE8XX series cards
3244-00010 - One low profile bracket for TC400 and TCE400 VoIP transcoding cards
Specialty Tools
Power Adapter: ST1
The Sangoma Power Adapter draws +12 V power from your standard PCIe slot and sends it to a standard Molex connector. Its unique design does not reduce the number of PCIe slots available in your system.
Crimping Tool: ST2
Use this kit of twelve RJ11/4 plugs and a crimping tool to hardwire your Sangoma A200 system.
Telco Patch Panel: STPP24
6 position, 2 conductor, 24-port/1 RMS (rack mount space) Telco patch panel. Integrated with 1 Telco connector and includes # 12 rack screws. Uses a female amphenol connector.
Sangoma's Tapping Tool
Sangoma’s T1/E1 line tapping solution is a high performance, robust and inexpensive toolkit that gives you complete access to the T1/E1 voice and signalling interfaces. Based on the popular A102, A104 and A108 AFT cards, the system supports the line tapping of one, two and four T1/E1 lines per card respectively.
Cables & Connectors
Twenty-four Port Rack Mount Patch Panel
The Digium 2400P Rack Mount Breakout Box is a 19 inch 1U, rack mountable patch panel featuring a 50-pin male connector and its 24 female RJ-11 connectors are wired with two conductors for single line operation.
Product Code: 1ACC24PPP
Four Port Interlocking Timing Cable
Up to four TE2/4XXP cards to share the same sync (timing) source from the T1/E1 provider, or provide a consistent sync source across multiple cards.
Product Code: 3112-00001
Six Foot 50-pin Male-to-Female Cable
The 6 foot 50-pin telephone cable interfaces the TDM2400P card with regular RJ-11 two-conductor telephone cables and is used in combination with either the 24-port, 2-wire breakout box (ACC2400PBO), or the 24-port, 2-wire 19″ rack mount unit (ACC2400PPP)
Product Code: 3113-00002
Three Port Interlocking Timing Cable
The timing cable allows up to three Hx8 or TE8xx cards to share the same sync (timing) source from the T1/E1 provider, or provide a consistent sync source across multiple cards.
Product Code: 3112-00003
Seven Foot T1/E1 Cable, Cross-Over, Shielded
The 7 foot shielded, cross-over cable is used for connecting Digium T1/E1 interface cards to the PSTN or other T1/E1 equipments. The cross-over cable is the standard cable that should be used to connect T1/E1 ports to T1/E1 ports or equipment.
Product Code: 3113-00016
RS232 DCE Cable:
CABL-607
For the A142, A144
Standard | ROHS: Yes | Length: 6′
V.35 DCE Cable:
CABL-608
For the A142, A144
Standard | Male | ROHS: Yes | Length: 6′
X.21 DCE Cable:
CABL-613
For Sangoma cards
Only Sold Separately | Length: 6′
RJ45 E1/T1 Cross over Cable:
CABL-614C
Back-to-back, cross over cable (x/o)
Special Order | ROHS: Yes | Length: 20’
RJ45 E1/T1 Cable:
CABL-614G
RJ45 E1/T1 Cable
Standard | ROHS: Yes | Length: 6′
A200 Analog Cable:
CABL-629
A200 Analog Cable
Standard | ROHS: Yes | Length: 6′
A108 T1/E1 “Portsplitter” Cable:
CABL-630
A400 DB25 Hard-wire Cable:
CABL-631
For a A400 Analog Cards
Standard | ROHS: Yes | Length: 6′
A400 Amphenol Y:
CABL-632
A200 Analog Cable
Standard | ROHS: Yes | Length: 6′
Fax Synch Cable:
CABL-633
Fax Synch Cable
Only Sold Separately | ROHS: Yes | Length: 8′
Dual Synch Cable:
CABL-633A
Dual Synch Cable
Only Sold Separately | ROHS: Yes | Length: 8”
BRI Cable:
CABL-634
For the A500 BRI
Standard | Length: 6′
Molex Power Adapter:
CABL-635
Power Adapter for FXS
Only Sold Separately | ROHS: Yes | Length: 8″
A142 Split RS232
CABL-636
Standard cable for A142R
A142 Split V.35/EIA530:
CABL-637
Standard cable for A142V
Standard | ROHS: Yes | Length: 1′
A144 Octopus RS232:
CABL-638
Standard cable for A144R
Standard | ROHS: Yes | Length: 1′
A144 Octopus V.35/EIA530:
CABL-639
Standard cable for A144V
Standard | ROHS: Yes | Length: 15′
SATA-Molex Power Adapter:
CABL-640
Only Sold Separately | ROHS: Yes | Length: 6″
T3 coax cables (Tx and Rx pair):
CABL-646
1 pair of 6’ BNC shielded Coaxial Cable for DS-3 Tx and Rx
RF Cable:
CABL-647
2-Ends Cable with SCSI Type connector:
CABL-648
Open-ended Cable with SCSI Type Connector to Panel:
CABL-649
7-Foot Twisted Pair Cable:
CABL-650
Single-mode fiber, LC duplex connectors:
CABL-651
Special Order Cables and Connectors
RS232 Back-to-Back Null-modem Cable:
CABL-601
Special Order
Only Sold Separately | Length: 10'
RS232 Back-to-Back Cable:
CABL-602
For connecting Sangoma cards to 3rd party DTEs
Special Order | Length: 4′
V.35 Back-to-Back Cable:
CABL-610
Special Order | ROHS: Optional | Length: 10′
EIA530 DCE Cable:
CABL-611
For Sangoma cards
ROHS: Optional | Length: 4′
USB FXO USB Cable:
CABL-641
For the USBfxo
Standard | Length: 6′
USB FXO/B600 FXS Cable:
CABL-642
For the USBfxo and B600 FXS
Standard | Length: 6′
B600 FXO Cable:
CABL-643
FXO Cable for the B600
Standard | ROHS: Yes | Length: 6′