Telephony Cards

We Have the Modules and Accessories You Need

Add-on hardware modules and accessories for analog and digital cards.

Sangoma
Sangoma
Sangoma

Telephony Card Add-Ons

Digium single channel analog modules allow 400 Series or 800 Series telephony cards to terminate one (1) line (FXO) or station (FXS) connections per module.

 

1S100MF  - Single Channel Station (FXS) Module

1X100MF - Single Channel Trunk (FXO) Module

1X100MF  - Single Channel Trunk (FXO) Module

Digium quad channel analog modules allow 800 Series or 2400 Series telephony cards to terminate four (4) line (FXO) or station (FXS) connections per module.

 

1S400MF - Quad Channel Station (FXS) Module

1X400MF - Quad Channel Trunk (FXO) Module

 

Digium Telephony boards come standard with full-height brackets for standard mounting. Optional low-profile brackets are available for all low-profile cards to enable mounting into 1-U servers.

 

3244-00052 - For Four (4) port A4 analog cards

3244-00044  - For One (1) Span TE133 and TE134 Digital Cards

3244-00048 - For Two (2) Span TE235 Digital Card

3244-00049 - For Four (4) Span TE435 Digital Card

FXS modules provide ringing voltage and battery to telephones or handsets and require substantial amount of 12V DC power in order to operate properly. The PCI interface on motherboards cannot provide sufficient quantities of this voltage necessary to ring 4, 8 or 24 modules. As a solution, Digium analog cards are mounted with a 4-pin disk-drive or Molex connector on the base board. This connector must be supplied with an internal power connector from the system's power supply if FXS modules are in use.

 

1PWR2401BLF - One external power supply bundle for analog card station (FXS) modules

1PWR2402BLF - Two external power supply bundle for analog card station (FXS) modules

 

 

DSP-based echo cancellation modules for all of our analog and digital (T1/E1/J1) cards with the VPMOCT series modules.

 

 

 

 

1VPMOCT256LF - Two Hundred and Fifty-Six (256) Channel Hardware 

1VPM128LF - One Hundred and Twenty-Eight (128) Channel Hardware 

1VPMOCT128LF - One Hundred and Twenty-Eight (128) Channel Hardware 

1VPM064LF - Sixty-four (64) Channel Hardware 

1VPMOCT064LF - Sixty-four (64) Channel Hardware

1VPM032LF - Thirty-two (32) Channel Hardware 

1VPMOCT032LF - Thirty-two (32) Channel Hardware 

 

 

Straight-through and cross-over cables for connecting Digium T1/E1 interface cards and T1/E1 ports, telephone cables for interfacing analog cards, and timing cables for digital cards.

 

 

 

3113-00016  - Seven (7) Foot T1/E1 cable, cross-over, shielded

1ACC24PPP - Twenty-four (24) port RJ-11 Nineteen (19) inch rack mount patch panel for 24 port analog cards

3113-00002 - Six (6) Foot 50-pin Male-to-Female cable for Twenty-Four (24) port analog cards

3112-00001 - Four (4) port interlocking timing cable for two (2) and four (4) span digital T1/E1 cards

3112-00003 - Three (3) port interlocking timing cable for HX8 and TE8XX series cards

3244-00010 - One low profile bracket for TC400 and TCE400 VoIP transcoding cards

Specialty Tools

The Sangoma Power Adapter draws +12 V power from your standard PCIe slot and sends it to a standard Molex connector. Its unique design does not reduce the number of PCIe slots available in your system.

Use this kit of twelve RJ11/4 plugs and a crimping tool to hardwire your Sangoma A200 system.

6 position, 2 conductor, 24-port/1 RMS (rack mount space) Telco patch panel. Integrated with 1 Telco connector and includes # 12 rack screws. Uses a female amphenol connector.

Sangoma’s T1/E1 line tapping solution is a high performance, robust and inexpensive toolkit that gives you complete access to the T1/E1 voice and signalling interfaces. Based on the popular A102, A104 and A108 AFT cards, the system supports the line tapping of one, two and four T1/E1 lines per card respectively.

Cables & Connectors

 

The Digium 2400P Rack Mount Breakout Box is a 19 inch 1U, rack mountable patch panel featuring a 50-pin male connector and its 24 female RJ-11 connectors are wired with two conductors for single line operation.

 

Product Code: 1ACC24PPP

 

Up to four TE2/4XXP cards to share the same sync (timing) source from the T1/E1 provider, or provide a consistent sync source across multiple cards.

 

Product Code: 3112-00001

The 6 foot 50-pin telephone cable interfaces the TDM2400P card with regular RJ-11 two-conductor telephone cables and is used in combination with either the 24-port, 2-wire breakout box (ACC2400PBO), or the 24-port, 2-wire 19″ rack mount unit (ACC2400PPP)

 

Product Code: 3113-00002

 

The timing cable allows up to three Hx8 or TE8xx cards to share the same sync (timing) source from the T1/E1 provider, or provide a consistent sync source across multiple cards.

 

Product Code: 3112-00003

The 7 foot shielded, cross-over cable is used for connecting Digium T1/E1 interface cards to the PSTN or other T1/E1 equipments. The cross-over cable is the standard cable that should be used to connect T1/E1 ports to T1/E1 ports or equipment.

 

Product Code: 3113-00016

For the A142, A144
Standard | ROHS: Yes | Length: 6′ 

 

 

For the A142, A144
Standard | Male | ROHS: Yes | Length: 6′ 

For Sangoma cards
Only Sold Separately | Length: 6′ 

Back-to-back, cross over cable (x/o)
Special Order | ROHS: Yes | Length: 20’

 

 

RJ45 E1/T1 Cable
Standard | ROHS: Yes | Length: 6′

 

A200 Analog Cable
Standard | ROHS: Yes | Length: 6′

 

For a A400 Analog Cards
Standard | ROHS: Yes | Length: 6′

 

A200 Analog Cable
Standard | ROHS: Yes | Length: 6′

 

Fax Synch Cable
Only Sold Separately | ROHS: Yes | Length: 8′

 

Dual Synch Cable
Only Sold Separately | ROHS: Yes | Length: 8”

 

For the A500 BRI
Standard | Length: 6′

 

 

Power Adapter for FXS
Only Sold Separately | ROHS: Yes | Length: 8″

 

Standard cable for A142R

 

Standard cable for A142V
Standard | ROHS: Yes | Length: 1′ 

Standard cable for A144R
Standard | ROHS: Yes | Length: 1′ 

Standard cable for A144V
Standard | ROHS: Yes | Length: 15′

 

Only Sold Separately | ROHS: Yes | Length: 6″

 

1 pair of 6’ BNC shielded Coaxial Cable for DS-3 Tx and Rx

 

Special Order Cables and Connectors

Special Order
Only Sold Separately | Length: 10'

For connecting Sangoma cards to 3rd party DTEs
Special Order | Length: 4′

Special Order | ROHS: Optional | Length: 10′

For Sangoma cards
ROHS: Optional | Length: 4′

For the USBfxo
Standard | Length: 6′

For the USBfxo and B600 FXS
Standard | Length: 6′

 

 

FXO Cable for the B600
Standard | ROHS: Yes | Length: 6′